2, Liitokala Lii402 USB package: Lii402 charger + USB cable + manual（Note: This package does not include a plug!）
Lii-402 Charger Manual
1. This charger can only charge cylindrical lithium ion battery (3.7V, 3.8V), nickel hydrogen / nickel cadmium, lithium iron phosphate battery;
2. Before use, please carefully refer to the instructions, pay attention to the recommended rechargeable battery charging current, do not exceed the recommended current charge;
3. Charge with a 5V USB adapter (adapter current recommended 2A);
4. Charger charge and discharge may be fever, be careful not to burn;
5. When you stop using it, unplug the power and unplug the battery.
6. Can only be used in normal room.
7. This product test data is for reference only, the actual situation, please refer to professional equipment.
Second, the charger requirements and functions:
1. Micro USB DC 5V input, two separate charging and microcomputer management system
2. Available for 4 kinds of charging current selection (500mA / 700mA / 1000mA / 2000mA) 2000mA designated fourth slot.
3. LED display Charge status 25% 50% 75% 100% and battery type NiMH 1.2V Li-Fe 3.2V Li-ion 3.7V Li-ion 3.85V.
4. Can automatically identify lithium (Li-ion) batteries and nickel-metal hydride (Ni-MH) batteries, manually select the iron phosphate (Liepo4) battery and Li-ion 3.85V battery
5. 0V voltage activation function, 1.65-1.85V can not be charged (but there will be activated current trickle type charge).
6. Have over-charge, short circuit, intelligent identification of bad batteries and reverse battery detection protection.
7. Charging mode, constant current constant pressure
8. Using DC input, the charger power supply for the 5V-2A (Micro plug)
9. With standard 5V / 1000mA USB automatic identification output function,
Third, the key, LED and function description
1. Press the key: hold the selector key for 2 seconds to switch 500mA 700mA 1000mA 2000mA charge current at power on,
When charging the battery, press the select key to change the type of rechargeable battery. When the rechargeable battery type is selected (for example, 3.20V 3.85V) for 5 seconds, enter the charging state.
2. LED: charger connected to the 5V power supply, the charger all the LED moment all bright, if the battery is not put into the charging slot, 500mA (LED) indicator light is on, the other lights go out.
When the battery is detected, the four LED lights are all bright, 3.7LED light will flash, then press the button to select the type of battery you need to charge, if not selected, 5 seconds into the default identification of the battery charge, charge The indicator light flashes at the corresponding charge ratio. Press the button to check the charge type (no power indication) 5 seconds after the return to the state of charge. When not energized, insert the battery to view the power ratio (5 seconds after extinguishing, need to view again press)
USB output indication: When the USB output is detected, the power indicator turns on for 10 seconds and presses to check the power.
Technology once again innovation, Auto-polarity detection. Do not need to distinguish the battery polarity. As long as the battery is rechargeable battery that can be charged. Do not worry about battery polarity reverse.Good Charger.
In addition to Auto-polarity detection there is a strong visible digi-dispaly. Visually beautiful. Function continues the Lii-100, very good.
Input: Micro USB DC 5V / 1A (min.)
Output voltage: DC 4.2V 500mA / 1000mA for Li-Ion
DC 4.35V 500mA / 1000mA for IMR
DC 3.65V 500mA / 1000mA for LeFePO4
DC 1.48V 500mA / 1000mA for NiMH / NI-Cd
Constant voltage charging with cut-off current less then 100mA
45 grams (charger) + 17grams (USB cable) included in delivery
1, One-slot charging and management system, Micro USB DC 5V input port
2, Battery polarity auto-detection (Any Polarity)
3, 500mAh / 1000mAh charging current for selection
4, Built-in digital tube indicator shows the real-time charging status of voltage and current
5, Identify Li-ion and Ni-MH battery automatically
Select manually by short-press the mode button for IMR battery (3.85V Li-ion) and LiFePO4 battery (3.2V)
6, Activation function for 0V battery of PCM protection.
7, Can not charge battery with 0.0U 0.2V for NiMH / Cd and 1.6U 2.2V for Li-Ion
8, Over-charging and over-discharge protection
9, Identify broken / defective battery
10, Charging under constant voltage and current
There's a 'MODE' button for choosing the battery types and charging current
Long press the 'MODE' button for 3 seconds to change the charging current, you can change the charging current at any time
Short press the 'MODE' button to change the charging types of lithium batteries. If no setting, it will default as 1.2V Ni-MH or 3.7V li-ion battery automatically. You need to change the mode for 3.85V li-ion and 3.2V LiFePO4 battery
It begins to charge the battery 5 seconds after your settings
When the battery is inserted or defective battery is inserted, the charger will have no any response showing "null" ; When the battery is fully charged, it shows "Full"
It can display the battery voltage and charge current by short press the 'MODE' button at any time during charging
2, Liitokala Lii202 USB package: Lii202 charger + USB cable + manual（Note: This package does not include a plug!）
This device is designed for portable, flexible and multiple battery types. it can detect the battery type and charging the battery is automatically selected in accordance with the charging current. Built-in LED indicators to show charging status and 5 V / 100 mAh USB output function
this charge is only for charging the cylindrical lithium-ion (3.7, 3.8), Ni-Mh / Ni-Cd, LiFePO4 (Li-Ion) batteries.
Please read these instructions before use; pay attention to the recommended charging current, never choose the wrong charging current
when the charge with 5V USB AC adapter, 2A-current AC adapter recommended
Charger ma hot during operation for a long time, handle with care!
please cut off the electricity and remove the battery from the charger when charging is complete.
indoor condition only !!
data mapping Charger for reference only; please refer to professional instrumentation, if you need accurate data
2. Features and Specifications:
Micro USB DC 5V input, two independent slots and charging channels with built-in micro-computer control system to ensure high efficiency
Two charging current parameters (0.5A / 1.0A)
Four LED indicators show the charging status (25%, 50%, 75%, 100%), and also shows the battery type, if inserted into the battery (1.2 V Ni-Mh, 3.2 in Li-Fe, 3.7 in Li-Ion, 3.85 in li-ion)
automatically identify Li-Ion and Ni-Mh; But, you need to adjust the charging mode for LiFePO4 and 3.85 in the lithium-ion battery
it can actively 0 V battery, but the device does not charge a 1.65 V ~ 1.85 V batteries types.
built with excessive charging protection, over-discharge protection and protection of polar reverse. besides, it can detect a broken battery.
Charing mode: instantaneous current and voltage.
PERMANENT charging current: Operating voltage in the 5V-2A (Micro-connector)
Standard automatic 5 V / 1000 mAh USB output port
3. Select the button, LED and function.
click to select the type of battery when inserting the battery. it will begin to charge the battery after fixing the battery type (please noted that it will automatically identify Li-Ion and Ni-Mh, no need to choose manually)
press and hold for 2 seconds, when after connecting to power, it can be switched between charging current of 0.5A and 1.0A;
connect the charger to power, all LED indicators will be on when the battery is inserted after 5 seconds, the LED will be turned off except for the indicator 0.5A current
when the battery is inserted into the device, 4 LEDs will be turned on and 3.7 V LED indictors blink, then please press the MODE button to set the correct type of battery. it will begin to charge the battery after 5 seconds, and the LED indictors show the charging status.
Press the MODE button to show the type of battery (5 seconds) during charging and return to show the charging status
it can show the remaining battery power, if you put the battery in the charger (with no connection to the power charging)
USB output indicator: When the USB output is detected, the volume of the battery indicators will be on for 10 seconds and then off, press the button to show the battery volume speed.
Input: Micro USB DC 5V / 2A
Output: 1.4, 4.2V ± 05, 3.65 ± 05, 4.35 ± 05
Output Current: 500/1000 mAh
constant voltage charging cut-off current: <100 mAh
Standby Current: <15 mAh
5. USB output function
USB output load voltage: 4.90 V-5.30
Output Current: 1000 mAh (1A)
Idle Current: <1 mAh
the output voltage of 4.75 V-5.25 V, when the current 1000 mAh
2, Liitokala Lii100 USB set: Lii100 charger + USB cable + manual（Note: This package does not include a plug!）
Lii-100 Charger Product description:
First, the charger requirements and functions:
1. Using micro USB DC 5V input, a single slot load and microcomputers management system Independent 2. Available two types of selection charge current (500mA / 1000mA)
3. LED displays the state of charge 25% 50% 75% 100% 1.2 V NiMH and Li-FE 3.0 V Li-ion 3.7 V Li-ion 3.85 V.
4. It can automatically identify the lithium battery (Li-ion) and nickel metal hydride batteries (Ni-MH) battery, manual processing iron phosphate selection (Liepo4) batteries and Li-Ion battery V 3.85 5. Ya 0 V driving voltage, 1.6-2.2 V does not charge (but donations will be activated current standard load flow). 6. Do not overload and over discharge, short circuit, intelligent recognition and detection Poor battery reversed protection battery. (Note: short circuit, bad battery, reversing the battery charger does not work, LED does not light)
7. Charge Mode, constant current constant voltage 8. Using a DC input power for the charger for V-1A work (Micro connector) 9. A paragraph: with standard 5 V / 1000 my USB automatic identification output,
B Section: No USB output function
secondly, a description of buttons, LEDs and function
1. Press: on, any time exercise the Select button for 2 seconds each 500mA charging current 1000mA converter;
battery-charging touch Select button to change the type of rechargeable battery, the battery must be recharged when the system chosen (eg, 3 V 3.85 V) 5/2 to enter the state of charge.
2. LED: charger plugged in 5 V power supply, charger, all LED full brightness instantly, without a battery in the charging slot, 500mA (LED) light, other lights go out.
upon detection of a battery, four LED lights flashing, then you can press the button to select the type of rechargeable batteries, if you do not choose, recognizing five seconds after entering the standard load, load indicator according the corresponding power ratio flash. press the button to see the standard price (no charge indicator) five seconds after the return to the state of charge. when not powered, insert the battery can be seen (5/2 and then off, you should see the press again)
USB output: when detected USB output power lights go after 10 seconds, the button can see the energy.
thirdly, electrical technical parameters:
1, input power: Micro USB DC 5v / 1a
2, the output voltage: 4.2 V ± 1% / 5V
3, the output current: 500mA / 1000mA
4, constant voltage charge, excluding current voltage <100 F;
5, the current external power source before: <15.0mA;
four USB output function:
1 voltage output load USB port: 4.90 to 5.30 V;
2, the output current: 1000mA
3 without load current: <1ma;
4, charging current 1,000, the door of the output voltage: 4.75 to 5.25 V;
5, protection voltage shutdown Output: 3.0 ± 0.1 V;
Input voltage: 100 ~ 240V 50 / 60HZ 0.3A (AC) Output voltage: 5V (DC) Output current: 2000MA Output socket: USB (standard) Output voltage accuracy: ± 0.3% (no load) Wide input range, high voltage accuracy Built-in IC program, can play the role of overload protection, please rest assured that use. Product performance characteristics: 1. Product built-in import management chip; 2. Constant current / constant voltage / constant temperature check mode charging, so that the charging current to maximize; 3 can activate the depth of discharge of the battery and reduce power consumption, the battery voltage Low when the use of low current pre-charge mode; 4. Power-down automatically enter the low-power mode of sleep mode charge. Features: 1, the charger for the USB output interface, can be used for mobile phone tablet computer equipment without interfering with each other 2 , The charger USB is 2A, to adapt to a wider range of electronic products 3, the charger shell for the ABS fire environmental protection materials, the use of smooth design, effectively prevent scratches to ensure that the beautiful appearance of the product 4, the charger built IC control protection circuit, over-voltage and over-current protection, the maximum protection of charging security, high efficiency, fast 5, versatile input design, continuous output voltage, built-in anti-electromagnetic interference filter, pay attention to your charge and use your Love machine; product color: (black white) color optional